Gauge Blocks

KOBA – Kolb and Baumann – Manufacturer of Precision Measuring Instruments - Products - Parallel End Gauges

Manufactured according to DIN EN ISO 3650

Kolb & Baumann has been manufacturing gauge blocks for more than 70 years. Today we are one of the few remaining manufacturers in Germany and Europe. Contrary to the general trend, we do not market Asian products. We are proud of producing our gauge blocks exclusively at our factory work floor in Aschaffenburg. This is the only way to monitor and guarantee the outstanding quality of our products. As a calibration laboratory accredited by the Deutsche Akkreditierungsstelle GmbH (DAkkS), we have the necessary measuring equipment to ensure the high quality standard.

Gauge blocks are a quality product:
more than 70 years of experience and research are background. The composition and purity of the material, the aging and stabilization methods, the processing, the dimensional control, the surface quality, the wear resistance, the sensible design of the storage boxes: all these aspects are subject to ongoing critical examination at KOBA

Gauge blocks

KOBA Gauge Blocks are manufactured and verified to the specifications of DIN EN ISO 3650. As tolerances are kept to a minimum by internal standards, it is guaranteed that every KOBA Gauge Block is within the limits stipulated. The high level of accuracy and the reliability of the measuring results are guaranteed by two separate feed-backs attributed to the internationally fixed unit of length by means of a wave length:

  • permanent comparison with master gauges interferometrically verified by the Physikalisch-Technische Bundesanstalt PTB
  • parallel to this calibration in our fully airconditioned laboratories

Tolerance ranges of the individual grades within the limits of which the actual size is guranteed, can be taken from the individual products. The durability of gauge blocks is achieved by a special process developed by us, combining natural and artifical ageing. The grade of accuracy should be selected according to the intended purpose:

K: Gauge blocks of calibration grade K with a DAkkS calibration certificate are ideally suited as the most accurate material measure of geometric length. They are used to check gauge blocks of the lower tolerance grades. Gauge blocks of calibration grade K always include a DAkkS calibration certificate. It shows the deviation from the nominal size for each gauge block.  

0: for all precise length measurements; for checking all gauge blocks in use; for final inspection; for setting measuring instruments

I: for checking gauges; for setting measuring instruments

II: as setting and working gauges in gauge and fixture construction as well as in general machine and apparatus engineering

On request and against reimbursement of costs, we can supply a calibration certificate from the Physikalisch-Technische Bundesanstalt. In most plants, one tolerance grade is not sufficient, as measuring accuracy varies greatly between departments and production stages. However, this very fact enables the most economical use of gauge blocks. If, for example, tolerance grade 0 gauge blocks are no longer accurate enough for inspection due to frequent use, they are passed on to a department or workstation with correspondingly lower requirements for measuring accuracy. However, it is advisable to send the gauge blocks to us for calibration before passing them on.

Gauge Blocks in Steel

KOBA steel gauge blocks: The carefully hardened and stress-relieved steel is a special steel. Its special melt gives it the highest possible degree of purity. The homogeneous distribution of the steel constituents and the resulting fine structure of uniform carbides provides excellent wear resistance. Sophisticated ageing methods prevent residual austenite from remaining and thus ensure the smallest possible dimensional change, which remains below the ISO specification.

  • up to 1000 mm according to DIN EN ISO 3650
  • grades K, 0, 1 und 2
  • single sizes available
  • standardised set compositions as well as customised set compositions
  • high wear-resistance
  • hardness > 800 HV
  • good stability in dimension due to extensive stabilisation process
  • thermal expansion coefficient
  • for Gauge Blocks in steel ≤ 100 mm α= 11,9 * 10^-6 K^-1
  • for Gauge Blocks in steel > 100 mm α= 11,2 * 10^-6 K^-1
  • traceable calibration certificate (laboratory accredited to DIN EN ISO/IEC 17025) included in delivery

Gauge Blocks in Ceramic

KOBA ceramic gauge blocks: The wear behaviour of KOBA ceramic gauge blocks is similar to that of carbide. The coefficient of expansion is closer to steel and is a=9.3· 10^–6 K^–1. Ceramic gauge blocks are not subject to corrosion and are therefore ideally suited for workshop use. The flexural strength of 800 N/mm2 is so high that there is no risk of breakage under normal use.

  • up to 100 mm
    in all tolerance grades
  • as individual gauge blocks
    in sets (also individual set compositions)
  • in minimum quantitiy customised lengths
  • corrosion resistant
  • approx. quadruble wear resistance of steel
  • high dimension stability due to Yttrium-stabilisation
  • coefficient of thermal expansion α= 9,3 * 10^ -6 K ^-1
  • traceable calibration certificate (laboratory accredited to DIN EN ISO/IEC 17025) included in delivery

Gauge Blocks in Carbide

KOBA carbide gauge blocks: The wear ratio compared to steel is approx. 1:50 to 1:100. As the outer measuring faces in particular are subject to wear in a gauge block combination, carbide gauge blocks are mainly used as protective gauge blocks. Every KOBA gauge block set has 2 empty slots for storing 1 or 2 mm carbide protective gauge blocks. The material used is tungsten carbide (coefficient of expansion 4.5 · 10^–6 K^–1). The use of carbide gauge blocks is particularly efficient where wear is greatest – in the workshop. However, you should use steel gauge blocks where steel workpieces are measured and it is not always possible to maintain exactly 20 °C. Otherwise, the difference in coefficients of expansion between carbide and steel leads to greater measurement uncertainties.

  • Carbide Gauge Blocks (Tungsten Carbide) according to DIN EN ISO 3650
  • up to 100 mm in tolerance grades K, 0, 1 and 2
  • as individual gauge blocks in sets, also with individual set composition
  • special designs upon enquiry
  • customised lengths – wear resistance approx. 1,5 times better in comparison to steel
  • hardness > 1.350 HV
  • best long-term stability of all materials
  • coefficient of thermal expansion α = 4,5 * 10 ^-6 K ^-1
  • traceable calibration certificate (laboratory accredited to DIN EN ISO/IEC 17025) included in delivery
KOBA – Kolb und Baumann – Hersteller für Präzisions-Messzeuge - Produkte - Prüfkörper für messmittel - Jutta Remmel - Ansprechpartner

Get in contact with us.

Jutta Remmel
Telefon: +49 6021/3463-13
Fax: +49 6021/3463-813
E-Mail:
jutta.remmel@koba.de

Accessories for Gauge Blocks

Matching our gauge blocks, you will find the appropriate accessories here for the correct handling of the products.